Crop pH and EC Lookup.
Crop pH and EC Lookup
The root-zone pH and EC your crop needs, and whether your own reading is in range.
Most greenhouse crops grow best with a substrate pH of 5.8 to 6.4, but two groups need their own range. Petunia, calibrachoa and the other iron-inefficient crops need 5.4 to 6.2, or their new leaves yellow from iron deficiency. Geranium, marigold and the other iron-efficient crops need 6.0 to 6.6, or they take up too much iron and manganese. For EC, light feeders such as impatiens and pansy want a PourThru reading of 1.0 to 2.6 mS/cm, medium feeders such as petunia and geranium 2.0 to 3.5, and heavy feeders such as poinsettia and mums 2.6 to 4.6. Pick your crop below for its ranges, then check a reading.
The three pH groups
Between pH 5.4 and 6.2 every nutrient is readily available (Purdue). The crop groups shift that window up or down, because crops differ in how well their roots take up iron. Iron-inefficient crops show iron deficiency, yellowing between the veins of the newest leaves, as soon as the pH drifts high. Iron-efficient crops take up so much iron and manganese at low pH that the lower leaves burn at the edges (e-GRO 6.10). Most crops sit in between. Purdue's grouping, from Paul Fisher's chapter in the Ball RedBook:
| Group | Substrate pH | Crops |
|---|---|---|
| Iron-inefficient | 5.4 to 6.2 | Bacopa, calibrachoa, nemesia, pansy, petunia, scaevola, snapdragon |
| General | 5.8 to 6.4 | Chrysanthemum, ivy geranium, impatiens, poinsettia, and most crops not listed |
| Iron-efficient | 6.0 to 6.6 | Geranium (seed and zonal), lisianthus, marigold, New Guinea impatiens |
Combination planters need a pH every crop in them can live with. A petunia group crop and a geranium group crop share only pH 6.0 to 6.2, a narrow target to hold; each overlaps the general group more widely.
Reading EC across test methods
All the common methods give the same pH, but not the same EC: for the same pot a 1:2 reads lowest and a PourThru highest (e-GRO 6.37). Compare a reading only with a target for the same method. Purdue's bands, after NC State, in mS/cm:
| PourThru | SME | 1:2 | Reads as | What it means |
|---|---|---|---|---|
| 0 to 0.9 | 0 to 0.75 | 0 to 0.25 | Very low | May not sustain rapid growth |
| 1.0 to 2.6 | 0.76 to 2.0 | 0.26 to 0.75 | Low | Suits seedlings, bedding plants and salt-sensitive crops |
| 2.7 to 4.6 | 2.1 to 3.5 | 0.76 to 1.25 | Normal | The standard range for most established plants |
| 4.7 to 6.5 | 3.6 to 5.0 | 1.26 to 1.75 | High | Reduced vigor and growth, especially in hot weather |
| 6.6 to 7.8 | 5.1 to 6.0 | 1.76 to 2.25 | Very high | Salt injury likely: marginal leaf burn and wilting |
| over 7.8 | over 6.0 | over 2.25 | Extreme | Most crops are injured; leach right away |
Which method to use. Use PourThru when the substrate holds controlled-release fertilizer, since prills in a scooped sample inflate the EC. Use SME, 1:2 or the squeeze method when you subirrigate, since salts collect at the top of the pot and a PourThru can wash them down into the sample. SME is less affected than 1:2 by how wet the sample is, and most commercial labs use it (e-GRO 6.37).
Every container crop listed
Feeder groups from Purdue's Table 1, adapted from NC State; pH groups from Purdue's Table 2. A crop with no pH group is one the source does not place in one; most crops do well at 5.8 to 6.4.
| Crop | Substrate pH | EC group (mS/cm) |
|---|---|---|
| African violet | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Ageratum | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Alstroemeria | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Alyssum | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Anemone | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Asclepias | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Aster | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Astilbe | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Azalea | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Bacopa | Iron-inefficient, 5.4 to 6.2 | Not listed |
| Begonia, fibrous | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Begonia, Hiemalis | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Begonia, Rex | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Begonia, tuberous | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Bougainvillea | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Caladium | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Calceolaria | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Calendula | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Calibrachoa | Iron-inefficient, 5.4 to 6.2 | Not listed |
| Calla lily | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Campanula | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Carnation | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Catharanthus (vinca) | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Celosia | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Centaurea | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Christmas cactus | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Chrysanthemum | General, 5.8 to 6.4 | Heavy: PourThru 2.6 to 4.6, SME 2.0 to 3.5 |
| Cleome | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Clerodendrum | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Coleus | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Cosmos | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Crossandra | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Cuttings, during rooting | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Cyclamen | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Dahlia | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Dianthus | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Dusty miller | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Exacum | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Freesia | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Geranium, ivy | General, 5.8 to 6.4 | Not listed |
| Geranium, seed | Iron-efficient, 6.0 to 6.6 | Not listed |
| Geranium, zonal (from cuttings) | Iron-efficient, 6.0 to 6.6 | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Gerbera | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Gloxinia | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Hibiscus | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Hydrangea | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Impatiens | General, 5.8 to 6.4 | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Kalanchoe | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Larkspur | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Lily, Asiatic and Oriental | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Lily, Easter | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Lisianthus | Iron-efficient, 6.0 to 6.6 | Not listed |
| Lobelia | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Marigold | Iron-efficient, 6.0 to 6.6 | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Morning glory | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Nemesia | Iron-inefficient, 5.4 to 6.2 | Not listed |
| New Guinea impatiens | Iron-efficient, 6.0 to 6.6 | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Orchids | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Ornamental kale | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Ornamental pepper | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Oxalis | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Pansy | Iron-inefficient, 5.4 to 6.2 | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Petunia | Iron-inefficient, 5.4 to 6.2 | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Phlox | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Platycodon | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Plugs | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Poinsettia | General, 5.8 to 6.4 | Heavy: PourThru 2.6 to 4.6, SME 2.0 to 3.5 |
| Portulaca | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Ranunculus | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Rose | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Salvia | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Scaevola | Iron-inefficient, 5.4 to 6.2 | Not listed |
| Snapdragon | Iron-inefficient, 5.4 to 6.2 | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Streptocarpus | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
| Sunflower, potted | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Verbena | 5.8 to 6.4 (most crops) | Medium: PourThru 2.0 to 3.5, SME 1.5 to 3.0 |
| Zinnia | 5.8 to 6.4 (most crops) | Light: PourThru 1.0 to 2.6, SME 0.76 to 2.0 |
Hydroponic vegetables and herbs
For crops grown in a recirculating or drain-to-waste nutrient solution, Oklahoma State's guide gives the EC and pH of the solution itself. These are not substrate readings and do not compare with the tables above.
| Crop | Solution EC (mS/cm) | Solution pH |
|---|---|---|
| Asparagus | 1.4 to 1.8 | 6.0 to 6.8 |
| Basil | 1.0 to 1.6 | 5.5 to 6.0 |
| Bean | 2.0 to 4.0 | 6.0 |
| Broccoli | 2.8 to 3.5 | 6.0 to 6.8 |
| Cabbage | 2.5 to 3.0 | 6.5 to 7.0 |
| Celery | 1.8 to 2.4 | 6.5 |
| Cucumber | 1.7 to 2.0 | 5.0 to 5.5 |
| Eggplant | 2.5 to 3.5 | 6.0 |
| Leek | 1.4 to 1.8 | 6.5 to 7.0 |
| Lettuce | 1.2 to 1.8 | 6.0 to 7.0 |
| Okra | 2.0 to 2.4 | 6.5 |
| Pak choi | 1.5 to 2.0 | 7.0 |
| Parsley | 1.8 to 2.2 | 6.0 to 6.5 |
| Pepper | 0.8 to 1.8 | 5.5 to 6.0 |
| Rhubarb | 1.6 to 2.0 | 5.5 to 6.0 |
| Sage | 1.0 to 1.6 | 5.5 to 6.5 |
| Spinach | 1.8 to 2.3 | 6.0 to 7.0 |
| Strawberry | 1.8 to 2.2 | 6.0 |
| Tomato | 2.0 to 4.0 | 6.0 to 6.5 |
| Zucchini (courgette) | 1.8 to 2.4 | 6.0 |
If a reading is off
e-GRO's corrective procedures (Alert 7.02), in short. Test a few plants first, and retest before repeating any treatment.
- pH too low (iron and manganese toxicity on lower leaves): switch to a basic fertilizer as the pH nears the bottom of the range. Flowable lime at 2 quarts per 100 gallons of water raises substrate pH by roughly 0.5 units.
- pH too high (yellowing between the veins of the upper leaves): switch to an acidic, ammonium-based fertilizer first. For a quicker drop, drench with water acidified to pH 4.0 to 4.5, with 5% to 10% leaching, then rinse the foliage.
- EC too low: raise the feed to 300 ppm N for a few applications, then return to the crop's normal rate.
- EC too high: if it is just creeping up, give a few clear-water irrigations. If it is very high, leach twice back to back with clear water, let the substrate dry down and retest; once it is back in range, feed a balanced fertilizer at 150 to 200 ppm N.
What it does not do
- It gives the published group ranges, not a cultivar's own. For optimum levels, e-GRO points growers to the crop plans from the seed companies (Alert 6.37).
- Ranges shift with crop stage: plugs and rooting cuttings sit in the light-feeder group even for crops that feed heavier later.
- It does not test anything. A good reading starts with a good sample: the same method, the same person, the same time after irrigation, distilled water, and meters calibrated weekly (e-GRO 6.37).
- It does not cover field soil, where pH targets and EC methods differ.
Learn more from the extension specialists
- e-GRO Alert 6.37, Monitoring pH and EC of Growing Medium (Cabrera and Raudales, UConn, 2017): the four test methods, step by step, and when to use each.
- e-GRO Alert 7.02, Corrective Procedures for Modifying Substrate pH and Electrical Conductivity (EC) (Whipker, Henry and Owen, 2018).
- e-GRO Alert 6.10, Manage pH with Water Soluble Fertilizers (Dickson, New Hampshire, 2017).
- e-GRO Alert 10.10, PourThru Method for Large Containerized Crops (Owen, Kentucky, 2021).
- e-GRO Alert 8.01, 1:2 Dilution Procedure: Determining Initial Substrate pH (Owen, Moore, Whipker and Henry, 2019).
- e-GRO Alert 5.15, Diagnosing Low Substrate pH Disorders (Whipker, NC State, 2016).
- Every e-GRO alert on substrate pH, indexed by crop and problem, in Greenhouse Alerts.
Sources
- Lopez, R.G., M.V. Mickelbart and C. Pasian. 2010. Alkalinity Management in Soilless Substrates. Purdue Extension HO-242-W. Table 2, media pH guidelines by group, from P. Fisher, "Managing pH for Container Media," Ball RedBook Vol. 2, 17th ed.
- Camberato, D.M., R.G. Lopez and M.V. Mickelbart. pH and Electrical Conductivity Measurements in Soilless Substrates. Purdue Extension HO-237-W. Table 1 (feeder groups) and Table 2 (EC bands by method), adapted from Cavins, Whipker, Fonteno, Harden, McCall and Gibson, NC State Horticulture Information Leaflet 590 (2000).
- Singh, H. and B. Dunn. 2016. Electrical Conductivity and pH Guide for Hydroponics. Oklahoma State HLA-6722. Table 2, solution EC and pH by crop.
- Cabrera, J. and R. Raudales. 2017. Monitoring pH and EC of Growing Medium. e-GRO Alert 6.37. Methods, method choice, EC equivalents and the 5.8 iron and manganese toxicity threshold for geraniums and New Guinea impatiens.
- Dickson, R. 2017. Manage pH with Water Soluble Fertilizers. e-GRO Alert 6.10. The 5.8 to 6.4 range for most crops (after Argo and Fisher 2002).
- Whipker, B.E., J. Henry and W.G. Owen. 2018. Corrective Procedures for Modifying Substrate pH and Electrical Conductivity (EC). e-GRO Alert 7.02.
CC BY 4.0. Cite as "Open Agriculture Technology Crop pH and EC Lookup (openagriculturetechnology.com)".
Frequently asked questions.
What pH should my potting mix be?
For most greenhouse crops, 5.8 to 6.4. Petunia, calibrachoa, pansy, snapdragon, bacopa, nemesia and scaevola need a lower 5.4 to 6.2, and geranium, marigold, New Guinea impatiens and lisianthus a higher 6.0 to 6.6 (Purdue Extension).
What is the best pH for petunias and calibrachoa?
5.4 to 6.2. Their roots are inefficient at taking up iron, so above that range the newest leaves turn yellow between the veins from iron deficiency. Keep their substrate on the low side, especially if your water is high in alkalinity (Purdue Extension).
What pH do geraniums need?
6.0 to 6.6 for seed and zonal geraniums. They take up iron and manganese efficiently, so when the substrate pH falls below about 5.8 they develop iron and manganese toxicity, with burned edges on the lower leaves (Purdue Extension; e-GRO Alerts 6.37 and 6.10). Ivy geraniums sit in the general group at 5.8 to 6.4.
What EC should my plants be?
It depends on the crop and the test method. By PourThru: light feeders such as impatiens, pansy, begonia and plugs 1.0 to 2.6 mS/cm; medium feeders such as petunia, geranium, hydrangea and verbena 2.0 to 3.5; heavy feeders, chrysanthemum and poinsettia, 2.6 to 4.6. By saturated media extract the same groups are 0.76 to 2.0, 1.5 to 3.0 and 2.0 to 3.5 (Purdue, after NC State).
What is a good EC and pH for hydroponic lettuce?
Oklahoma State's guide gives an EC of 1.2 to 1.8 mS/cm and a pH of 6.0 to 7.0 for lettuce in a hydroponic solution. Basil is 1.0 to 1.6 at pH 5.5 to 6.0, and tomato 2.0 to 4.0 at pH 6.0 to 6.5.
Why does my PourThru EC not match my lab's number?
Each method dilutes the sample differently, so the same pot reads differently. e-GRO's example: a PourThru of 1.0, an SME of 0.75 and a 1:2 of 0.25 mS/cm are the same "very low" level. Most labs use SME. Compare each reading only with targets for its own method; pH readings agree across methods.
Which substrate test method should I use?
Use PourThru when the substrate holds controlled-release fertilizer, and SME, 1:2 or squeeze when you subirrigate. Whichever you choose, keep it the same each time: the same method, person and time after irrigation, distilled water, and meters calibrated weekly (e-GRO Alert 6.37).
How do I raise or lower substrate pH?
To raise it, switch to a basic fertilizer, and if it is already too low, apply flowable lime at 2 quarts per 100 gallons, which raises it by roughly half a unit. To lower it, switch to an acidic, ammonium-based fertilizer first; for a faster drop, drench with water acidified to pH 4.0 to 4.5. Retest before repeating either (e-GRO Alert 7.02).