Calculators · Water, nutrients & feed

Alkalinity and Acid Calculator.

What this is
Calculator
Domain
Water, nutrients & feed
Account
None needed
Use
In the browser, or embed

Alkalinity and Acid Calculator

How much acid to add to your water to reach a target pH, the nutrients the acid brings with it, and what it costs.

The amount of acid your water needs is set by its alkalinity, not its pH. Alkalinity is the bicarbonate that soaks up acid, and each milliequivalent per liter of it (50 ppm as calcium carbonate) takes about 11 fluid ounces of 35% sulfuric acid, or about 6.8 of 67% nitric acid, per 1,000 gallons to bring the water to pH 5.8. Enter your water test below for a starting amount, the nitrogen, phosphorus or sulfur the acid adds, and the cost, then confirm with a pH meter after mixing.

Calculate your acid

From your water test. Alkalinity is the number that matters most; the starting pH refines it.

Your water

From the lab report or a test kit
5.8 is the usual end point

Your acid and batch

Sulfuric 35% is sold as battery electrolyte
From the label
Typical value; your SDS, section 9, has yours

How the calculation works

Alkalinity in irrigation water is almost all bicarbonate, with some carbonate in water above about pH 8.3. Acid turns bicarbonate into carbonic acid, which is carbon dioxide dissolved in water. The calculator works out how much bicarbonate and carbonate your water holds from its pH and alkalinity, then how much of it is left at your target pH, using the carbonic acid constants (pKa 6.35 and 10.33 at 25 °C). The difference is the alkalinity the acid has to neutralize, in milliequivalents per liter.

That is why alkalinity, not pH, sets the dose. Bailey's example from NC State: water at pH 9.3 with 71 ppm alkalinity needed 46.6 mL of 35% sulfuric acid per 100 gallons to reach pH 5.8, while water at pH 8.3 with 310 ppm alkalinity needed 203.0 mL. The water a full pH unit lower took four times the acid. This calculator gives 47.9 mL and 203.4 mL for those two waters, within 3% and 0.2% of NC State's figures.

The acid side is plain arithmetic. Each acid gives up a known number of hydrogen ions at the target pH: two for sulfuric, one for nitric, about one for phosphoric (its second hydrogen barely lets go below pH 7), and about two for citric at pH 5.8. From the strength on the label and the specific gravity, the calculator turns milliequivalents into milliliters and fluid ounces, or grams for dry citric acid. The nutrient the acid carries (sulfur, phosphorus or nitrogen) comes out of the same arithmetic.

One honest difference: NC State's 1994 table lists 7.3 fl oz of 75% phosphoric acid per meq per 1,000 gallons. The chemistry here gives about 8 fl oz, because it counts one full hydrogen per phosphoric acid molecule. If you use phosphoric acid, start near the lower figure and let your pH meter decide.

Choosing an acid

AcidAddsWhat the sources say
Sulfuric, 35% or 93%SulfurThe most common choice: inexpensive and relatively safe (Purdue). NC State recommends it over nitric and phosphoric for ease, safety, cost and availability.
Phosphoric, 75% or 85%PhosphorusCount the P toward your feed. At high alkalinity it can supply far more P than the crop needs: 6 meq/L of alkalinity treated with phosphoric acid supplies over 126 ppm P (NC State).
Nitric, 67%NitrogenThe hardest of the three to handle safely (NC State). The same 6 meq/L water would get 67 ppm N from it.
Citric, dryNothing the plant uses as a nutrientListed by Purdue among the acids injected for alkalinity. A dry powder you weigh, not pour.

What it does not do

  • It treats the water by itself. Fertilizers move pH too: acid-residue feeds (ammonium) pull it down and basic-residue feeds push it up (Purdue). Mix the acid in first, then the feed, then measure.
  • It assumes the carbon dioxide the acid makes stays in the water. In an open tank some of it leaves, and the pH drifts up a little after mixing. Measure again after the tank has stood.
  • It does not size an injector. With an injector, the acid for a batch goes into the stock the injector draws to make that batch: at 1:100, the acid for 1,000 gallons goes into 10 gallons of stock.
  • It is a starting amount, not a final one. NC State's own advice is to fine-tune with a meter.

Learn more from the extension specialists

Sources

  • Bailey, D.A. 1994. "Water Acidification." N.C. Flower Growers' Bulletin 39(3), North Carolina State University. Table 1 (acid per meq of alkalinity and the nutrient each supplies), the two worked examples, the 5.8 end point and the handling advice. PDF.
  • Lopez, R.G., M.V. Mickelbart and C. Pasian. 2010. Alkalinity Management in Soilless Substrates. Purdue Extension HO-242-W. The 120 ppm rule of thumb, unit conversions and the choice of acids.
  • Carbonic acid constants pKa1 6.35 and pKa2 10.33 at 25 °C, as given in standard water chemistry texts.
  • Specific gravities are typical values for each strength; the safety data sheet for your product, section 9, gives its own.

CC BY 4.0. Cite as "Open Agriculture Technology Alkalinity and Acid Calculator (openagriculturetechnology.com)".

Frequently asked questions.

How much acid do I need to lower the alkalinity of my irrigation water?

It depends on the alkalinity, not the pH. As a starting point, NC State's table gives 11.0 fl oz of 35% sulfuric acid, 6.8 fl oz of 67% nitric acid or 7.3 fl oz of 75% phosphoric acid per 1,000 gallons for each meq/L (50 ppm as CaCO₃) of alkalinity, to reach about pH 5.8. Water with 200 ppm alkalinity (4 meq/L) needs about 44 fl oz of 35% sulfuric acid per 1,000 gallons.

How do I lower the pH of my well water for plants?

Get the water tested for alkalinity as well as pH, then add a measured amount of acid: sulfuric is the most common, with phosphoric, nitric and citric as the alternatives. The alkalinity tells you how much acid it takes. Mix the acid into the water first, add fertilizer after, and check the result with a pH meter.

What is the difference between pH and alkalinity in water?

pH measures how acidic or basic the water is right now. Alkalinity measures how much acid the water can absorb before its pH falls, mostly as bicarbonate. Two waters with the same pH can need very different amounts of acid, and it is alkalinity, more than pH, that pushes up the pH of the growing medium over time.

What alkalinity is too high for irrigation water?

Purdue Extension's rule of thumb is that water above about 120 ppm alkalinity as CaCO₃ is likely to cause high substrate pH, and is worth acidifying. Small containers and plug trays are more sensitive than large pots, because there is less medium to buffer the water.

Which acid is best for lowering water pH: sulfuric, phosphoric, nitric or citric?

Sulfuric acid is the most common because it is inexpensive and relatively safe, and NC State recommends it over nitric and phosphoric. Phosphoric adds phosphorus and nitric adds nitrogen, which you count toward your feed; at high alkalinity phosphoric can add far more phosphorus than the crop needs. Citric adds no plant nutrient.

How do I convert alkalinity from meq/L to ppm?

Multiply meq/L by 50 to get ppm (mg/L) as calcium carbonate. If your lab reports bicarbonate (HCO₃⁻) in ppm, divide it by 61 to get meq/L. So 4 meq/L is 200 ppm as CaCO₃, or about 244 ppm bicarbonate.

Does acidifying water add nutrients?

Yes. Sulfuric acid adds sulfur, phosphoric adds phosphorus and nitric adds nitrogen. Each fluid ounce per 1,000 gallons supplies about 1.13 ppm S from 35% sulfuric, 2.88 ppm P from 75% phosphoric, or 1.64 ppm N from 67% nitric (NC State). The calculator shows the amount for your water so you can take it off your fertilizer.

Can I use battery acid to lower water pH?

Battery electrolyte is sulfuric acid at about 35%, and it is the product NC State's 1994 bulletin recommended for acidifying greenhouse water. Use one sold as plain electrolyte, wear eye protection and gloves, and add acid to water, never water to acid.